Skip to content
Yardox

How many boxes of laminate flooring do I need?

The box count is the easy part: room area plus waste, divided by the area in one box. The part that changes the answer is the layout, because a strip that is too narrow or a joint too close to the one beside it sends boards to the bin.

Updated November 10, 2026

Short answer

Buy the room area plus at least 10 %, as Lowe’s advises, and divide by the area printed on the box. A 4.2 × 3.45 m room needs 15.94 m², which is 7 boxes of 2.28 m². Leave 8–10 mm at the walls for Quick-Step, 10–15 mm for HARO, 3/8 in for Pergo.

Calculate it

Laminate and vinyl calculator

Packs, underlay, skirting and last-row width.

Laminate and vinyl calculator →

From room area to boxes

Area to buy = room area × (1 + waste). Boxes = area to buy divided by the area in one box, rounded up. Lowe’s advises buying at least 10 % more flooring than you plan to use, to cover cuts and mistakes.

Measure the room as a rectangle, wall to wall. The expansion gap is hidden under the skirting and does not reduce what you buy. If the room is not a rectangle, split it into rectangles and add them up before applying the waste.

Worked example, metric: 4.2 × 3.45 m

Boards 190 × 1200 mm (0.228 m² each), planks running along the 4.2 m side, ten to a box (2.28 m²), gap 10 mm.

  • Area: 4.2 × 3.45 = 14.49 m².
  • With 10 % waste: 15.94 m².
  • Boards: 15.94 / 0.228 = 69.9, so 70 boards.
  • Boxes: 15.94 / 2.28 = 6.99, so 7 boxes.

The 70 boards are exactly seven boxes of ten. If the figure had come to 7.01, you would buy eight. When the result lands this close to a whole number, recheck your measurements before ordering.

Worked example, imperial: 14 × 11 ft

Planks 7 × 48 in, which is 2.33 sq ft each, gap 3/8 in.

  • Area: 14 × 11 = 154 sq ft.
  • With 10 % waste: 169.4 sq ft.
  • Planks: 169.4 / 2.33 = 72.6, so 73 planks. Divide by the sq ft printed on the box to get boxes.

Expansion gap and large rooms

A floating floor has to move with temperature and humidity, so it must not touch walls, pipes or door frames. The required gap depends on the maker.

Expansion gap and size limits in the installation instructions
MakerGap at wallsIntermediate joint or T-moulding
Quick-Step8–10 mm (5/16–3/8 in)over 13 m in length or width
HARO10–15 mm (0.4–0.6 in)over 10 m (33 ft) in length or width
Pergo3/8 in on all sidesrooms 40 ft (12.2 m) or more in length or width; doorways 4 ft (1.22 m) or less

Lowe’s also gives 3/8 in. Use the figure in the instructions for the floor you bought. The calculator defaults to 10 mm in metric and 3/8 in in imperial, and you can change it.

The last row: how narrow is too narrow

Boards are laid across the width of the room, so after the gap and the full rows there is a leftover strip at the far wall. Quick-Step says that if the last row would be less than 40 mm (about 1.6 in) wide, you should cut the first row down as well, so that both edge rows are wider. HARO says to cut the boards of the last row to size on the long side and fit them in, keeping the gap. Pergo says to trace the wall contour with a full-width plank as a spacer.

In the metric example the width is 3.45 m, less 10 mm at each wall is 3.43 m. Eighteen full boards of 190 mm take 3.42 m and leave 10 mm. A 10 mm strip cannot be laid, so the first and last rows are each cut to (190 + 10) / 2 = 100 mm. The room then has 19 rows.

This costs nothing extra in boxes. You are cutting the same area, just in two strips instead of one.

Offset of end joints

End joints in neighbouring rows must not line up. The minimum offset differs: Quick-Step asks for at least 30 cm (12 in), Pergo for at least 6 in, and HARO for at least 50 cm (20 in). Pergo also says the first piece in a row must be at least 8 in long.

HARO tells you to reuse leftover pieces for the next row, so the cut-off end of one row can start the next as long as it respects the offset. Plan the first board of each row with that in mind.

Before laying, Quick-Step says to leave the unopened packs in the room for 48 hours at room temperature, ideally 15–22 °C and 30–75 % relative humidity. Lowe’s gives a minimum of two days.

Questions

How much extra laminate should I buy?

Lowe’s advises at least 10 % more than the room area, for cuts and mistakes.

How many boxes of laminate for a 12 × 12 ft room?

The room is 144 sq ft; with 10 % waste you need 158.4 sq ft. Divide by the sq ft per box printed on your boxes and round up.

How big should the expansion gap be?

Quick-Step gives 8–10 mm, HARO 10–15 mm and Pergo 3/8 in (about 9.5 mm). Follow the instructions for your floor.

What is the minimum width of the last row?

Quick-Step says 40 mm: if the last row would be narrower, cut the first row too. Other makers do not give a number, so check your instructions.

How far apart must end joints be?

At least 30 cm with Quick-Step, 6 in (about 15 cm) with Pergo and 50 cm with HARO.

Does the same apply to vinyl plank?

The box arithmetic does. The instructions quoted here are for laminate, so for vinyl plank take the gap and offset from the maker’s sheet. The calculator treats both the same way.

Calculate it

Laminate and vinyl calculator

Packs, underlay, skirting and last-row width.

Laminate and vinyl calculator →

Sources

  1. [1]Installation instructions for Quick-Step laminate with Hydroseal technology. Quick-Step (Unilin). Expansion gap 8–10 mm; if the last row would be less than 40 mm, cut the first row too; end joints staggered at least 30 cm. Checked November 5, 2026
  2. [2]PERGO XP Install Instructions (2019_03_XP_SML). Pergo (Unilin). Expansion space 3/8 in on all sides; end joints offset at least 6 in; first piece at least 8 in long. Checked November 5, 2026
  3. [3]Installation instructions for laminate flooring with Top Connect (08/22). HARO. Expansion gap 10–15 mm; end joints offset at least 50 cm. Checked November 5, 2026
  4. [4]How to Install Laminate Flooring. Lowe's. Buy at least 10 % more flooring than you plan to use, for cuts and mistakes. Checked November 5, 2026