Short answer
A roofing square is 100 sq ft (9.29 m²) of roof surface. GAF lists 3 bundles per square for Timberline HD, and Mike Guertin of Fine Homebuilding calls 3 the most common, with heavy shingles needing 4 or 5. Add 1 % waste for a simple roof and 5 % or more for a complex one.
Bundles per square
A square covers 100 sq ft of roof. The GAF Timberline HD data sheet lists 3 bundles per square, and Guertin writes that three bundles to the square is most common. He puts one bundle at about 33.3 sq ft. Heavier three-tab and laminated shingles take four, sometimes five bundles to cover a square.
The bundle count therefore changes with the product, so read it off the wrapper or the data sheet of the shingle you buy before you multiply.
| Bundles per square | Roof area per bundle | Typical for |
|---|---|---|
| 3 | 33.3 sq ft (3.10 m²) | GAF Timberline HD; most three-tab and light laminated |
| 4 | 25 sq ft (2.32 m²) | heavier three-tab and laminated |
| 5 | 20 sq ft (1.86 m²) | heaviest laminated |
The area per bundle is 100 divided by the bundles per square. The 4 and 5 bundle rows are Guertin's range for heavy shingles; the page does not tie them to particular products.
From the footprint to roofing squares
Measure the house outline at the eaves, overhangs included, and multiply length by width. That is the plan area, what a bird sees from above. It is not the area you shingle, because a sloped roof is bigger than the ground under it.
Multiply the plan area by the pitch factor of the roof. The factor is the length of the slope divided by the horizontal run, which is the square root of 1 plus (rise ÷ 12)² when pitch is written in inches of rise per 12 in of run. The calculator applies it for you; the table shows how fast it grows.
| Pitch (rise:run) | Angle | Factor |
|---|---|---|
| 4:12 | 18.4° | 1.054 |
| 6:12 | 26.6° | 1.118 |
| 8:12 | 33.7° | 1.202 |
| 12:12 | 45.0° | 1.414 |
Divide the roof area by 100 sq ft (9.29 m²) to get squares. A 6:12 roof with a 1,344 sq ft footprint has 1,344 × 1.118 = 1,503 sq ft of surface, or 15.03 squares before waste.
Worked example: a 6:12 gable roof, in feet
House 40 × 30 ft with a 1 ft overhang on every side, so the roof plan is 42 × 32 ft = 1,344 sq ft. Pitch 6:12, shingles at 3 bundles per square.
- Surface: 1,344 × 1.118 = 1,503 sq ft.
- Simple gable, 1 % waste: 1,518 sq ft = 15.18 squares = 45.5 bundles, so 46.
- Same roof with 5 % waste for cuts and mistakes: 1,578 sq ft = 15.78 squares = 47.3 bundles, so 48.
Guertin uses 1 % for a simple roof and 5 % or more for a complex roof with valleys. He adds that fall-off pieces, valley trimmings and damaged shingles can total up to 5 % of the shingles a house needs, and that a conscientious crew usually needs one extra bundle.
Worked example: the same idea in metres
House 12 × 9 m with a 0.3 m overhang all round, so the roof plan is 12.6 × 9.6 m = 120.96 m². Pitch 6:12 (26.6°), 5 % waste.
- Surface: 120.96 × 1.118 = 135.2 m².
- With waste: 135.2 × 1.05 = 142.0 m², which is 15.28 squares.
- One bundle at 3 per square covers 3.10 m², so 142.0 / 3.10 = 45.9 bundles, which rounds up to 46.
Round once at the end, on the whole roof, not per slope.
Starter strip and ridge caps
Starter shingles go along the eaves. Guertin describes them as shingles with the exposure trimmed off, leaving the self-seal strip and top lap, and GAF lists ProStart and WeatherBlocker as the starter for Timberline HD. Starter along the rakes is optional and gives a neater edge. He says not to cut rake starters from full laminated shingles, because the exposure portion is too thick.
To count them, measure eaves and rakes, round up to the next foot and divide by three, which gives the number of 3 ft starter pieces. For the 42 ft gable above, two eaves are 84 ft, so 28 pieces. Metric: two eaves of 12.6 m are 25.2 m, which is 27.6 lengths of 0.9144 m, so 28.
Hip and ridge caps are bought by length. Guertin says a bundle of companion ridge shingles typically caps about 35 linear ft (10.7 m) of ridge or hip, and tells you to confirm that with your supplier. GAF names Timbertex, Seal-A-Ridge, Z Ridge and Ridglass for Timberline HD and notes they are not sold everywhere. A 42 ft ridge needs 42 / 35 = 1.2 bundles, so 2. A 12.6 m ridge needs 12.6 / 10.67 = 1.18, also 2.
Questions
How many bundles of shingles make a square?
Three for most shingles, including GAF Timberline HD. Heavier shingles need four or five. The wrapper states the number.
How many square feet does a bundle of shingles cover?
At 3 bundles per square, one bundle covers about 33.3 sq ft (3.10 m²) of roof. Guertin gives the same figure.
How do I convert my roof to squares?
Multiply the footprint by the pitch factor (1.118 at 6:12), then divide by 100 sq ft, or by 9.29 m². Add waste before you divide into bundles.
How much waste should I allow?
About 1 % on a simple roof and 5 % or more on a complex roof with valleys, according to Guertin.
How many bundles of ridge caps do I need?
Divide the ridge and hip length by the coverage printed on the bundle. Guertin gives about 35 linear ft (10.7 m) per bundle as typical; check your product.
Do I need starter shingles on the rakes?
Along the eaves, yes. Along the rakes they are optional and only give a neater edge.
Sources
- [1]Timberline HD Lifetime Shingles, technical data sheet (10/26/2015). GAF. 3 bundles per square (100 sq ft); exposure 5⅝ in; shingle 13¼ × 39⅜ in.. Checked November 5, 2026
- [2]Don't Fall Short on Shingles: How to Estimate Materials for Roofing Projects. Mike Guertin, Fine Homebuilding. Waste about 1 % on a simple roof, 5 % or more on a complex roof with valleys; starter along eaves (rakes optional); hip and ridge caps by length, a bundle typically caps about 35 linear ft; three bundles per square is most common, heavy shingles need four or five.. Checked November 5, 2026