Short answer
Cut each strip as wall height plus 4 in (about 10 cm), count the strips by dividing the wall width by the roll width and rounding up, then check how many strips one roll yields. Brewster gives the 4 in; Christopher Farr advises at least 10 % extra.
Length of one strip
Brewster Wallcovering says to measure the wall height and add 4 inches: 2 inches at the top and 2 inches at the bottom, which you trim off after hanging. For a wall 8 ft high, each strip is 8 ft 4 in, or 100 in. For a 2.5 m wall it is about 2.6 m.
Measure the height from the skirting to the cornice, or to the ceiling if there is no cornice, as Christopher Farr describes.
How many strips fit the wall
Each strip is called a drop. Christopher Farr counts them by dividing the wall width by the width of the wallpaper and always rounding up to a whole number. If the walls share a height, add their widths together first; the total width of a 4 × 5 m room is 18 m.
With a roll 50 cm wide (a round figure for the sums, not a standard; read the width on your label), 18 m ÷ 0.5 m = 36 drops. In inches, 60 ft of wall is 720 in; with a 20 in roll that is also 36 drops.
This count ignores doors and windows. That keeps the result on the safe side.
Pattern repeat and match
Arte International defines three cases. With a free match (no pattern) the strips go side by side with nothing to line up. With a straight match the pattern sits at the same height on every strip. With an offset match the pattern is shifted in height from one strip to the next.
For a patterned paper, Christopher Farr cuts each drop in whole repeats. Divide the wall height by the repeat height to get the whole repeats, add one more repeat for each drop, and multiply by the repeat height to get the drop length. For a half-drop pattern, add half a repeat on top of that.
Take a wall of 2.5 m and a repeat of 60 cm. 250 ÷ 60 gives 4 whole repeats, plus 1 makes 5, and 5 × 60 = 300 cm per drop. A half-drop version adds 30 cm and is 330 cm. The label shows the repeat and the match; Brewster notes that the match decides whether you must account for the repeat when you cut the next strip.
From strips to rolls
Multiply the drops by the drop length for the paper you need, then check how many whole strips come out of one roll. A strip cannot be joined from two pieces without breaking the pattern, so leftover ends at the bottom of each roll are lost. Example: 36 drops, rolls 10 m long (again an example length; use the one on your label).
| Paper | Drop length | Paper in total | Strips per roll | Rolls |
|---|---|---|---|---|
| Free match, wall 2.5 m + trim | 2.60 m | 93.6 m | 3 | 12 |
| Straight match, repeat 60 cm | 3.00 m | 108.0 m | 3 | 12 |
| Half-drop, repeat 60 cm | 3.30 m | 118.8 m | 3 | 12 |
| Straight match, repeat 120 cm | 3.60 m | 129.6 m | 2 | 18 |
The last row shows why dividing total length by roll length misleads: 129.6 ÷ 10 is 13 rolls, but only two 3.6 m strips fit in each roll, so you need 18.
In inches: a wall 8 ft high gives 100 in strips. Sixty feet of wall with 20 in rolls is 36 drops, and a roll 30 ft long (360 in) yields 3 strips of 100 in. That is 12 rolls.
Spare paper
Christopher Farr advises adding at least 10 % for wastage. It applies to the paper you calculated, so work it out before you round to whole strips per roll.
The wallpaper calculator linked below does the drop count, the repeat and the strips per roll from your wall sizes and the label values.
Questions
How long should I cut each strip of wallpaper?
Wall height plus 4 inches, says Brewster: 2 inches at the top and 2 inches at the bottom for trimming. With a pattern, round the length up to whole repeats.
How do I calculate the number of drops?
Divide the wall width by the width of the roll and round up, as Christopher Farr describes.
What is a drop match?
The terms vary by maker. Arte defines straight match (pattern at the same height on every strip), offset match (pattern shifted in height from strip to strip) and free match (no pattern to line up). Half-drop is the case where each drop gains half a repeat.
How much extra wallpaper should I buy?
Christopher Farr advises at least 10 % for wastage, plus the allowance for the repeat.
Do I need to subtract doors and windows?
The count above leaves them in, which keeps it on the safe side. Add the 10 % wastage allowance on top.
How wide and how long is a roll?
It differs by maker and market, so read the width, length and repeat on the label. Both are inputs of the calculation.
Sources
- [1]How to Measure and Cut Wallpaper. Brewster Wallcovering. Strip length = wall height + 4 in: 2 in at the top and 2 in at the bottom for trimming.. Checked November 5, 2026
- [2]How to Calculate Wallpaper Quantities. Christopher Farr Cloth. Drops = wall width / roll width, rounded up; drop length in whole pattern repeats; a half-drop pattern adds half a repeat to each drop.. Checked November 5, 2026
- [3]FAQ: Ansatz (straight, offset and free match). Arte International. Definitions of straight match (pattern at the same height on every strip), offset match and free match.. Checked November 5, 2026