In breve
Measure every wall run that gets trim, leave out the door openings, and then plan the cuts board by board. A 12 × 14 ft room is 52 ft of baseboard, but with 8 ft boards and a 1/8 in saw kerf the cuts need 8 boards, not 7.
Calcola
Calcolatore battiscopa e profili
Quante barre comprare e come tagliarle.
Calcolatore battiscopa e profili →Start from the wall lengths, not the floor area
Baseboard follows the walls, so the starting point is a list of runs: the length of each wall, with any door opening taken out as its own break. Measure each run along the floor, to the corner or to the door casing.
For mitred corners, measure each run to the long point of the board, because a mitre makes the back edge shorter than the face. The calculator linked below does not add an allowance for corners. The cut lengths it plans are the run lengths you enter, so enter them as the board will actually be cut.
What happens to a wall longer than the board
A run longer than one stock board is made from whole boards plus a remainder. A 14 ft wall with 8 ft boards becomes one full 8 ft board and a 6 ft piece. A 3.6 m wall with 2.4 m boards becomes a full board and a 1.2 m piece. Each place where two boards meet is a join, so the number of joins is worth knowing before you start.
The remainders are the pieces that decide how many boards you buy. The full-length pieces use up a board each and waste nothing. The short remainders have to share boards, and that is a packing problem.
Fitting the cuts onto stock lengths
The calculator first places the longest piece on the first board that still has room, then the next longest, and so on. That is quick and often good enough. If the result uses more boards than the theoretical minimum (total length including kerfs, divided by one board and rounded up), it searches through the other arrangements and stops when it finds the minimum or runs out of its search limit. In the second case it says the plan may not be the best possible.
The saw kerf is the width of the blade, which turns into dust. Each cut costs one kerf. The calculator counts a kerf after every cut and lets the last cut on a board run to its end, so a board holds its length plus one kerf.
This is why the kerf matters most for pieces that add up to exactly one board. Two 4 ft pieces cannot come out of one 8 ft board if the blade removes 1/8 in between them.
Worked example in feet and in metres
Imperial: a 12 × 14 ft room, four runs of 12, 12, 14 and 14 ft, 8 ft boards, 1/8 in kerf. The 12 ft walls become 8 + 4 ft and the 14 ft walls become 8 + 6 ft. That is four full boards and remainders of 4, 4, 6 and 6 ft. No two remainders fit on one board once the kerf is counted, so the plan is 8 boards (64 ft) for 52 ft of trim. With zero kerf the two 4 ft pieces could share a board and 7 boards would do.
Metric: a 3.0 × 3.6 m room, runs of 3.6, 3.6, 3.0 and 3.0 m, 2.4 m boards, 3 mm kerf. The 3.6 m walls become 2.4 + 1.2 m and the 3.0 m walls become 2.4 + 0.6 m. Four full boards, and the remainders 1.2 and 0.6 m go together on two more boards. The 1.2 + 1.2 m pairing would need 2.406 m, so it does not fit. Total: 6 boards (14.4 m) for 13.2 m of trim, with about 1.19 m of offcut.
| Imperial | Metric | |
|---|---|---|
| Room | 12 × 14 ft | 3.0 × 3.6 m |
| Trim needed | 52 ft | 13.2 m |
| Stock board | 8 ft | 2.4 m |
| Kerf | 1/8 in | 3 mm |
| Boards to buy | 8 | 6 |
| Joins | 4 | 4 |
A join in the middle of a long wall is normal. Where the short piece goes is your choice, so put it where it shows least.
Doors, openings and the shopping list
Each wall with a door is two runs, one on each side of the opening. Enter them separately; a short run of 0.4 m or 1 ft is exactly the kind of piece that fills the end of a board.
Order the number of boards from the plan, not from the total length. If your supplier sells several lengths, run the plan once per length and compare the board counts and the price per metre or foot.
Domande
How much baseboard do I need for a room?
Add the length of every wall that gets baseboard and take out the width of any door openings. A 12 × 14 ft room is 52 ft, a 3 × 3.6 m room is 13.2 m. Then plan the cuts, because the boards you buy are longer than the total.
Should I add extra for mitred corners?
The calculator adds no corner allowance and plans the lengths you enter. Measure each run to the long point of the mitre so the piece is cut to the right length.
Why does the calculator say 8 boards when the length divided by 8 ft is 6.5?
Pieces of 4, 4, 6 and 6 ft each take most of a board. Once the saw kerf is counted, no two of them fit on one 8 ft board, so the short pieces use a board each.
What if the search stopped early?
The plan shown is still valid and cuttable. It only means the calculator did not finish proving that no arrangement uses fewer boards. Try fewer distinct run lengths or a different stock length.
Do I count the kerf for every cut?
Yes, every cut that does not end at the board end removes one blade width. A 2 to 3 mm kerf is small on one cut and decisive when two pieces add up to exactly one board.
Calcola
Calcolatore battiscopa e profili
Quante barre comprare e come tagliarle.
Calcolatore battiscopa e profili →Fonti
- [1]Handbook 44, Appendix C: General Tables of Units of Measurement. National Institute of Standards and Technology (NIST). 1 ft = 12 in = 0.3048 m (exact). Verificato il 6 novembre 2026