In breve
A 6/12 pitch is 26.6° or 50 %. Degrees = arctan(rise / 12); percent = rise / 12 × 100. The rafter is longer than its run by the slope factor, √(12² + rise²) / 12, which is 1.118 for a 6/12 roof.
Calcola
Calcolatore lunghezza dei travetti del tetto
Lunghezza dei travetti, pendenza del tetto, angoli di taglio e numero di travetti.
Calcolatore lunghezza dei travetti del tetto →Pitch, degrees and percent
A pitch of 6/12 means the roof rises 6 in for every 12 in it runs horizontally. The Saskatchewan Indian Institute of Technologies carpentry manual describes slope as a ratio, an angle or a percentage, and all three describe the same line.
Angle in degrees is arctan(rise / run). Percent is rise divided by run, times 100. At 12/12 the roof rises as far as it runs: 45° and 100 %. A 100 % slope is not vertical.
| Pitch (rise / 12) | Degrees | Percent |
|---|---|---|
| 2/12 | 9.5° | 16.7 % |
| 3/12 | 14.0° | 25.0 % |
| 4/12 | 18.4° | 33.3 % |
| 5/12 | 22.6° | 41.7 % |
| 6/12 | 26.6° | 50.0 % |
| 7/12 | 30.3° | 58.3 % |
| 8/12 | 33.7° | 66.7 % |
| 9/12 | 36.9° | 75.0 % |
| 10/12 | 39.8° | 83.3 % |
| 12/12 | 45.0° | 100 % |
To go the other way, from degrees to a pitch over 12, multiply the tangent of the angle by 12. A 30° roof is tan 30° × 12 = 6.93, close to 7/12. A 35° roof is 8.40/12.
Slope factor: how much longer the rafter is than its run
A rafter lies along the hypotenuse of a right triangle whose legs are the run and the rise. For 12 in of run the rafter measures √(12² + rise²) inches. Divided by 12, that is the slope factor: multiply any horizontal run by it to get the length along the slope.
The same factor converts roof area. A roof surface is the plan area times the slope factor, so a 6/12 roof has 11.8 % more surface than the footprint under it.
| Pitch | Slope factor | Rafter per 12 in of run |
|---|---|---|
| 2/12 | 1.014 | 12.17 in |
| 3/12 | 1.031 | 12.37 in |
| 4/12 | 1.054 | 12.65 in |
| 5/12 | 1.083 | 13.00 in |
| 6/12 | 1.118 | 13.42 in |
| 7/12 | 1.158 | 13.89 in |
| 8/12 | 1.202 | 14.42 in |
| 9/12 | 1.250 | 15.00 in |
| 10/12 | 1.302 | 15.62 in |
| 12/12 | 1.414 | 16.97 in |
The carpentry manual works one case through: a 4/12 roof with 16 units of run has a rafter line length of 12.65 in × 16 = 202.4 in (16 ft 10⅜ in) and a total rise of 4 in × 16 = 64 in.
Rafter length from the pitch
First find the run. On a gable roof the run of a common rafter is half the building width, less half the thickness of the ridge board (Journal of Light Construction, Framing Workbook). Multiply the run by the slope factor.
The JLC measures the rafter from the top plumb cut to the building line, so the overhang is not included. The tail is figured separately: the manual gives tail length as the unit line length times the overhang.
Imperial: a 24 ft wide building with a 6/12 roof has a run of 12 ft, ignoring the ridge. Length = 12 × 1.118 = 13.42 ft, about 13 ft 5 in, and the rise is 6 ft. With a 1½ in ridge board the run is 143.25 in, the length 143.25 × 1.118 = 160.2 in. A 12 in overhang adds a tail of 12 × 1.118 = 13.4 in.
Metric: an 8 m wide building at 35° has a run of 4 m. The slope factor is 1 / cos 35° = 1.221, so the rafter is 4 × 1.221 = 4.88 m and the rise is 4 × tan 35° = 2.80 m. A 0.4 m overhang adds a 0.49 m tail.
These are theoretical lengths. Add cutting waste and check the plumb and seat cuts against your actual framing before you cut a full set.
Minimum pitch for asphalt shingles
IRC R905.2, as summarised by the City of Hopkins, Minnesota, allows asphalt shingles only on slopes of 2 units vertical in 12 horizontal (2:12) or steeper. From 2:12 up to 4:12 the code requires double underlayment.
2:12 is 9.5° or 16.7 %, and 4:12 is 18.4°. A roof shallower than 2:12 needs a different type of covering. Your local code and the shingle maker's instructions may differ from the model code, so check both before you order.
Domande
What is a 6/12 roof pitch in degrees?
arctan(6 / 12) = 26.6°. As a percentage it is 50 %, and the slope factor is 1.118.
What roof pitch is 45 degrees?
12/12, a rise of 12 in for every 12 in of run. That is a 100 % slope.
How do I convert degrees to pitch?
Multiply the tangent of the angle by 12. For 20°, tan 20° × 12 = 4.37, so about 4.4/12.
What is the minimum pitch for asphalt shingles?
2:12 (9.5°) under IRC R905.2, with double underlayment between 2:12 and 4:12. Always confirm with your local building department.
Does rafter length include the overhang?
Not in the JLC method. Rafter length is measured from the top plumb cut to the building line, and the tail is added separately as the overhang times the unit line length.
Calcola
Calcolatore lunghezza dei travetti del tetto
Lunghezza dei travetti, pendenza del tetto, angoli di taglio e numero di travetti.
Calcolatore lunghezza dei travetti del tetto →Fonti
- [1]Cutting Common Rafters (Framing Workbook, Training the Trades). Journal of Light Construction. Run of a common rafter on a full gable roof is half the building width minus half the ridge thickness; rafter length is measured from the top plumb cut to the building line and does not include the overhang.. Verificato il 10 novembre 2026
- [2]Carpentry Refresher Program Manual, Topic 2: Gable Roof Components and Calculations (CC BY 4.0). Saskatchewan Indian Institute of Technologies. Slope as degrees, percent or unit rise in 12; total rise = unit rise × units of run; line length by Pythagoras; tail length = unit line length × overhang. Worked example: 4/12, 16 units of run gives 202.4 in (16 ft 10⅜ in) and 64 in of rise.. Verificato il 10 novembre 2026
- [3]Asphalt shingles (IRC R905.2), city building department summary. City of Hopkins, MN. Asphalt shingles only on slopes of 2:12 or more; double underlayment from 2:12 to 4:12.. Verificato il 10 novembre 2026