Sheet cutting optimizer
Lay out the pieces you need on standard sheets of plywood, OSB, MDF or drywall, with the saw cut between them, and see how many sheets to buy and where to cut.
Sheet
The width of your saw blade, usually 2–4 mm (1/8 in).
Pieces to cut
Cutting plans
Add this calculator to your website
Free for any website: paste this code where the calculator should appear. It keeps itself up to date, fits its height to the content and links back to the full page with the explanations.
Come si usa
- 01Enter the size of the board you buy, for example 2500 × 1250 mm for plywood or 96 × 48 in for a 4 × 8 sheet.
- 02Enter the saw blade width. A circular or track saw blade is usually about 2 to 3 mm, or 3/32 to 1/8 in; the exact value is printed on the blade.
- 03List the pieces with width, height and quantity. One line per size is enough.
- 04Choose whether pieces may be turned. Say no for veneered boards, wood grain or patterned surfaces that must all run one way.
- 05Read the number of sheets, then follow the cutting plan for each sheet. The numbers on the pieces match the lines of your list.
Come si calcola
The optimizer places pieces the way a panel saw cuts them: every cut runs straight across the remaining part of the board, from one edge to the other. These guillotine cuts are what you can make with a track saw, a table saw or a panel saw without plunging into the middle of a board.
- Piece with blade
- (w + kerf) × (h + kerf)
- Usable board
- (W + kerf) × (H + kerf)
- Fewest possible sheets
- ceil(total piece area / sheet area)
- Yield
- total piece area / (sheets × sheet area)
Pieces are sorted from the largest to the smallest. Each one goes into the free rectangle where it leaves the least waste (best area fit), and the leftover is split along its shorter side, a rule described by Jukka Jylänki in his 2010 survey of rectangle packing methods.
Every piece takes one blade width more on its right and top side, because the saw turns that strip into dust. The last piece next to the board edge needs no cut, so the board is counted one blade width larger.
The fewest possible sheets is a lower limit no layout can beat. When the plan needs more sheets than that, the pieces simply do not fit together better with straight cuts, or a different order would save a sheet. Packing is a hard problem, and the plan is a good one, not always the best possible.
Esempio svolto
Cabinet parts from 2500 × 1250 mm boards, 3 mm blade
- Pieces: 4 × 800 × 600, 2 × 1200 × 400 and 6 × 600 × 300 mm, 12 pieces in all.
- Piece area: 4 × 0.48 + 2 × 0.48 + 6 × 0.18 = 3.96 m². One board is 3.125 m², so at least 2 boards are needed.
- The plan fits everything on 2 boards: the first one 79 % used, the second 48 %.
- Yield: 3.96 / 6.25 = 63 %. The rest of the second board stays as an offcut for shelves or test cuts.
Come fare l'ordine giusto
Check the real board size
Boards from the store are often slightly over or under the nominal size, and the factory edges can be chipped. Measure, and trim a few millimetres off one long and one short edge if you need clean edges.
Cut the large pieces first
Follow the plan from the long cuts that run across the whole board. Smaller parts are easier to handle after the board is split.
Mark every piece
Write the piece number on each part right after cutting. It saves mixing up parts of similar size later.
Keep grain direction in mind
For visible fronts and side panels the grain should usually run the long way. Switch rotation off for those boards and enter width and height in the grain direction.
Errori comuni
- Forgetting the blade width. With a 3 mm blade, ten cuts across a board take 30 mm, enough to make the last piece too short.
- Allowing rotation on veneered or patterned boards and ending up with grain in two directions.
- Entering finished sizes for parts that get edge banding or a trim cut later. Add that allowance to the piece size.
- Planning without a spare. One wrong cut on the last board means a trip back to the store.
Domande
How many sheets of plywood do I need?
At least the total area of all pieces divided by the area of one sheet, rounded up. The cutting plan shows whether the pieces really fit into that many sheets with straight saw cuts.
What kerf should I enter?
The width of the cut your blade makes. It is printed on the blade, usually as the tooth width. Most circular and track saw blades cut 2 to 3.2 mm.
Why does the plan use one sheet more than the minimum?
The minimum assumes pieces fill every corner. With straight cuts from edge to edge, some shapes leave gaps that nothing else fills. Try allowing rotation, or adjust a size slightly.
Can I use this for drywall or tiles?
Yes for any rectangular board that you cut straight. For drywall on walls and ceilings the drywall calculator counts sheets for whole areas.
Calcolatori correlati
Fonti
- [1]A Thousand Ways to Pack the Bin – A Practical Approach to Two-Dimensional Rectangle Bin Packing (J. Jylänki, 2010). RectangleBinPack (GitHub). Guillotine packing: each placed piece splits its free rectangle in two by a straight cut through the whole rectangle; free rectangle chosen by best area fit, split along the shorter leftover axis; pieces sorted by area, largest first.. Verificato il 11 novembre 2026
Formule e fonti verificate l'ultima volta il 11 novembre 2026. Come calcoliamo