Naar de inhoud
Yardox
Deze taalversie wordt nagekeken door een moedertaalspreker. Sommige formuleringen kunnen nog veranderen.

Construction unit converter

Convert the units you meet on a building site and in product data: lengths, areas, volumes and weights, but also roof and drain slopes, U- and R-values, heating power and pressure.

What do you want to convert?

Value

Add this calculator to your website

Free for any website: paste this code where the calculator should appear. It keeps itself up to date, fits its height to the content and links back to the full page with the explanations.

Zo gebruik je de calculator

  1. 01Pick what you want to convert: length, area, volume, weight, temperature, slope, pressure, heating power, U-value, R-value or thermal conductivity.
  2. 02Enter the value and the unit it is in.
  3. 03Pick the unit you need. The table shows the value in every other unit at the same time.

Zo werkt de berekening

Each value is turned into the SI unit of its kind and back into the unit you want. The factors are those of the NIST Guide to the SI; the foot, inch, yard, mile and pound are exact by the 1959 international agreement.

Any unit
value × factor(from) / factor(to)
Temperature
°F = °C × 1.8 + 32, K = °C + 273.15
Slope
% = 100 × rise / run, ° = arctan(rise / run), x/12 = 12 × rise / run
U and R
1 Btu/(h·ft²·°F) = 5.678263 W/(m²K); R 1 = 0.1761102 m²K/W

Area and volume factors follow from the length factors: 1 ft² = 0.09290304 m², 1 yd³ = 0.764555 m³. The US gallon is 231 cubic inches, the acre 43,560 square feet.

For heat the calculator uses the International Table Btu, the one used in US product data: 1 Btu/h = 0.2930711 W, and a ton of refrigeration is 12,000 Btu/h, or 3.517 kW.

A slope given as 1 : n means one unit of rise over n units of run. It has no value for a flat slope.

Rekenvoorbeeld

Common conversions on site

  1. 10 ft = 3.048 m. 1 m = 3.281 ft = 3' 3 3/8".
  2. 1 yd³ of concrete = 0.765 m³; 1 m³ = 1.308 yd³.
  3. Roof pitch 6/12 = 50 % = 26.6°. Drain fall 2 % = 20 mm/m = 1 : 50.
  4. US R-19 = RSI 3.35 m²K/W. U 0.2 W/(m²K) = 0.035 Btu/(h·ft²·°F).

Tips voor je bestelling

Check which ton

A US ton is 2,000 lb (907 kg), a metric tonne 1,000 kg. Delivery notes for gravel and asphalt use either, depending on the country.

Read R-values with the unit

A US R-13 and a European R of 13 are very different: R-13 in US units is only RSI 2.3. Always check which unit a label uses.

Slope in percent is not degrees

100 % is 45°, not 90°. For small slopes percent and mm per metre are the clearest.

Veelgemaakte fouten

  • Converting square feet to square metres with the length factor. Square the factor: 1 ft² is 0.0929 m², not 0.3048.
  • Confusing US and imperial gallons. This calculator uses the US gallon of 3.785 litres.
  • Mixing up U-value and R-value. U is heat flow, R is resistance: a higher R and a lower U both mean better insulation.

Veelgestelde vragen

How many square feet in a square metre?

10.764 ft². One square foot is 0.0929 m².

How do I convert cubic yards to cubic metres?

Multiply by 0.7646. One cubic metre is 1.308 cubic yards.

How do I convert a US R-value to RSI?

Multiply by 0.1761. R-19 is RSI 3.35, R-30 is RSI 5.28.

What is 6/12 roof pitch in degrees?

26.6°. It is a 50 % slope: 6 inches of rise per 12 inches of run.

How many Btu/h is 1 kW?

3,412 Btu/h. A 12,000 Btu/h air conditioner or heat pump has 3.5 kW.

Bronnen

  1. [1]NIST Guide to the SI (SP 811), Appendix B.9: Factors for units listed by kind of quantity. National Institute of Standards and Technology. Btu_IT = 1055.056 J; Btu_IT/h = 0.2930711 W; Btu/(h·ft²·°F) = 5.678263 W/(m²K); Btu·in/(h·ft²·°F) = 0.1442279 W/(mK); °F·h·ft²/Btu = 0.1761102 m²K/W; psi = 6894.757 Pa; bar = 10⁵ Pa exactly; ton of refrigeration = 3516.853 W; US gallon = 3.785412 L; short ton = 907.1847 kg; yard = 0.9144 m and mile = 1609.344 m exactly.. Gecontroleerd op 11 november 2026

Formules en bronnen voor het laatst gecontroleerd op 11 november 2026. Hoe we rekenen