Cut list optimizer
Plan how to cut studs, battens, pipes, profiles or rebar from the lengths your supplier sells: how many to buy, which lengths, and where every cut goes.
Lengths you can buy
Pieces are placed on as few lengths as possible, with the saw cut between them. With several stock lengths, each one gets the cheapest length that still holds its cuts.
Add every length the yard or shop stocks. With prices for all of them, the plan aims for the lowest cost; without, for the least length bought.
Pieces to cut
Saw
The width of the blade, lost at every cut.
Cut off each length first to square a rough or damaged end. 0 if the ends are clean.
Cutting plans
- Length 1 · 6000 mmOffcut: 41 mm
#1 2.400 mm · #1 2.400 mm · #2 1.150 mm
- Length 2 · 6000 mmOffcut: 41 mm
#1 2.400 mm · #1 2.400 mm · #2 1.150 mm
- Length 3 · 6000 mmOffcut: 182 mm
#2 1.150 mm · #2 1.150 mm · #2 1.150 mm · #2 1.150 mm · #3 600 mm · #3 600 mm
- Length 4 · 6000 mmOffcut: 2.382 mm
#3 600 mm · #3 600 mm · #3 600 mm · #3 600 mm · #3 600 mm · #3 600 mm
Add this calculator to your website
Free for any website: paste this code where the calculator should appear. It keeps itself up to date, fits its height to the content and links back to the full page with the explanations.
Cum se folosește
- 01Enter every stock length your supplier sells, with its price if you want the cheapest mix.
- 02List the pieces you need: their length and how many.
- 03Enter the width of your saw blade, and a trim if the ends of the stock need squaring.
- 04Read how many lengths to buy and follow the cutting plan for each one. Copy or print it for the saw.
Cum se calculează
This is a packing problem: fit the pieces onto as few stock lengths as possible. Every cut also eats the width of the blade, so each piece takes its length plus one kerf. The pieces are sorted from longest to shortest and each one goes onto the first length with room left. With a single stock length, a search then tries other arrangements until it either finds a plan with fewer lengths or proves that none exists.
- Space a piece takes
- piece length + kerf
- Usable length of a stock
- stock length − trim + kerf
- Fewest lengths possible
- (sum of pieces + kerfs) / usable length, rounded up
- Offcut
- stock length − trim − cuts − kerfs
The usable length gets one kerf back because the last piece can run to the end of the stock without a cut after it.
With several stock lengths, the pieces are packed once for each length and then every packed length is given the cheapest stock that still holds its cuts, or the shortest one when not all prices are known. The best of these plans is shown. It mixes lengths well, but with several stock lengths it is not proven to be the cheapest possible.
Exemplu de calcul
Battens from 6 m and 3 m lengths
- Pieces: 4 × 2400 mm, 6 × 1150 mm, 8 × 600 mm; saw cut 3 mm.
- Total of the pieces: 9.6 + 6.9 + 4.8 = 21.3 m, so at least four 6 m lengths.
- Two 2400 mm pieces fit on a 6 m length with 1150 mm beside them: 2403 + 2403 + 1153 = 5959 mm, under 6003 mm.
- The calculator shows the full plan and the offcut on every length.
Cum comanzi cantitatea potrivită
Check what lengths are really in stock
Yards list lengths they do not always have. Enter only the lengths you can actually get.
Measure your blade
A thin-kerf blade and a thick one can change the plan on a long list. Use the width of the blade you will cut with.
Cut the longest pieces first
Follow the plan in order. If a length turns out to have a defect, a long piece is harder to fit elsewhere than a short one.
Keep the offcuts labelled
Offcuts from one plan are often long enough for blocking, noggins or a later job.
Greșeli frecvente
- Forgetting the saw cut: on 20 cuts a 3 mm blade eats 60 mm.
- Planning with a damaged or out-of-square end and losing the last piece.
- Mixing units: stock in feet and pieces in inches is fine here, but check the unit next to every field.
Întrebări
Is this the best possible plan?
With one stock length the calculator says so when it has proven that no plan uses fewer lengths. With several stock lengths it gives a very good plan, not a proven one.
Can a piece be longer than the stock?
Not in this calculator: it plans whole pieces. For runs that can be joined, such as skirting, use the baseboard calculator, which splits long walls.
Why does a longer stock length sometimes cost less?
Because the pieces fit with less offcut. The calculator compares the lengths with your prices and picks the cheapest mix it finds.
Does it work for metal and plastic?
Yes. The plan is pure geometry: pipes, rails, profiles and rebar are cut the same way. Enter the kerf of your cutting tool.
Calculatoare conexe
Surse
- [1]Handbook 44, Appendix C: General Tables of Units of Measurement. National Institute of Standards and Technology (NIST). 1 ft = 12 in = 0.3048 m (exact). Verificat la 6 noiembrie 2026
Formulele și sursele au fost verificate ultima dată la 6 noiembrie 2026. Cum calculăm