Short answer
CMHA calls for a compacted aggregate base of at least 4 in (100 mm) under patios and sidewalks and at least 6 in (150 mm) under residential driveways on well-drained soil, plus 1 in (25 mm) of bedding sand. Dig base + sand + paver thickness: about 7.4 in (185 mm) for a patio.
Calculate it
Paver calculator
Pavers, gravel base, bedding sand, edging and joint sand.
Paver calculator →How thick is the base?
The Concrete Masonry & Hardscapes Association (CMHA) sets the minimum compacted base at 4 in (100 mm) for patios and sidewalks and 6 in (150 mm) for residential driveways, over well-drained soils. Rochester Concrete Products gives ranges: 4 to 6 in for foot traffic and 8 to 12 in for vehicles. It says to use the lower end on well-drained or undisturbed soil and the upper end on poorly drained or disturbed soil.
So there is a gap for driveways: 6 in is CMHA's floor on good soil, and a paver maker may ask for more. Take the thicker figure if the soil is soft, wet or fill, or if heavy trucks will use the drive.
Compact the base in lifts. CMHA describes spreading and compacting it in lifts of 4 to 6 in (100 to 150 mm), so a 4 in patio base goes in as one lift and an 8 in driveway base as two.
Bedding sand and the total dig
The bedding layer is a nominal 1 in (25 mm), measured before the pavers are compacted into it. CMHA is clear that sand is not there to correct an uneven base: screed it over a base that is already flat and sloped. Rochester names coarse sand, such as concrete sand, for the job.
Excavation depth is the sum of the layers. CMHA gives no single figure, so you add it up yourself:
| Layer | Patio | Driveway on good soil |
|---|---|---|
| Compacted base | 4 in (100 mm) | 6 in (150 mm) |
| Bedding sand | 1 in (25 mm) | 1 in (25 mm) |
| Paver | 2.36 in (60 mm) | 2.36 in (60 mm) |
| Dig this deep | 7.4 in (185 mm) | 9.4 in (235 mm) |
Rochester lists a total excavation of 7 to 9 in for pedestrian areas and 11 to 15 in for vehicle areas. Thicker pavers add 3/4 to 1⅝ in on top.
Slope and joints
CMHA asks for a surface slope of at least 1.5 %, which is 15 mm per metre or about 3/16 in per foot, so that water runs off. Build the slope into the base, not into the sand.
Joints between pavers are 1/16 to 3/16 in (2 to 5 mm) wide. If you fill them with polymeric sand, Rochester gives one 50 lb bag per 60 to 75 sq ft with narrow joints and per 25 to 40 sq ft with wide joints.
Worked example: a 12 × 15 ft patio
Area: 12 × 15 = 180 sq ft (16.7 m²).
- Base at 4 in: 180 × (4 / 12) / 27 = 2.22 yd³ of aggregate, using Rochester's formula of paver area × base depth. In metric, a 10 m² patio with a 100 mm base is 1.0 m³.
- Bedding sand at 1 in: 180 × 0.0031 = 0.56 yd³, Rochester's factor. For 10 m² at 25 mm it is 0.25 m³.
- Polymeric sand, narrow joints: 180 / 75 = 2.4 and 180 / 60 = 3.0, so 3 bags of 50 lb.
- Excavation: 4 + 1 + 2.36 = 7.4 in (185 mm).
The pavers calculator linked below sums these layers and converts the volumes to weight using a bulk density.
How many extra pavers for cuts
Western Interlock says to add 10 % for straight-lay patterns and 15 to 20 % for diagonal, herringbone or curved layouts.
For the 180 sq ft patio that is 198 sq ft of pavers with a straight pattern and 207 to 216 sq ft with herringbone. Metric: 10 m² becomes 11.0 m², or 11.5 to 12.0 m² for herringbone.
Questions
How thick should the gravel base be under pavers?
CMHA gives at least 4 in (100 mm) for patios and sidewalks and 6 in (150 mm) for residential driveways, compacted, on well-drained soil. Rochester suggests 8 to 12 in for vehicle areas.
How much sand goes under pavers?
A nominal 1 in (25 mm) of bedding sand, measured before compaction. Do not use it to level an uneven base.
How deep should I dig for a patio?
Base plus sand plus paver thickness. With a 4 in base, 1 in of sand and a 60 mm paver, about 7.4 in (185 mm).
How many extra pavers should I buy?
Western Interlock says 10 % extra for straight patterns and 15 to 20 % for diagonal, herringbone or curved layouts.
What slope should a paver patio have?
At least 1.5 %, per CMHA, which is about 15 mm per metre or 3/16 in per foot.
How wide are the joints?
Between 1/16 and 3/16 in (2 to 5 mm), according to CMHA.
Calculate it
Paver calculator
Pavers, gravel base, bedding sand, edging and joint sand.
Paver calculator →Sources
- [1]Construction of Interlocking Concrete Pavements (PAV-TEC-002-22). Concrete Masonry & Hardscapes Association (CMHA, formerly ICPI). Aggregate base at least 4 in (100 mm) for sidewalks and patios and 6 in (150 mm) for residential driveways on well-drained soils, thicker on wet or weak soils; bedding sand 1 in (25 mm) uncompacted; base compacted in 4–6 in lifts; joints 2–5 mm; slopes at least 1.5 %; pavers 60 mm thick for pedestrian areas and driveways.. Checked November 6, 2026
- [2]How to calculate paver stones needed for your project. Western Interlock (Basalite Building Products). Add 10 % for straight-lay patterns, 15–20 % for diagonal, herringbone or curved layouts.. Checked November 6, 2026
- [3]Paver Installation Guide (2018). Rochester Concrete Products. Base volume = paver area × base depth; polymeric sand, 50 lb bag per 60–75 sq ft with narrow joints or 25–40 sq ft with wide joints.. Checked November 6, 2026
- [4]Classification of aggregates (after Mindess, Concrete). Penn State University, CE 584 course library. Normal-weight aggregate (gravel, crushed stone): dry-rodded unit weight 1100 to 1750 kg/m³.. Checked November 5, 2026
- [5]Material conversions for winter parking lot and sidewalk maintenance. Minnesota Pollution Control Agency, Minnesota Stormwater Manual. Clean sand: 1 cubic yard = 1.4 tons (1.66 t/m³); weight varies with moisture.. Checked November 5, 2026
- [6]Produktdatenblatt Bruchsand 0/2. Leube Baustoffe. Crushed sand 0/2: bulk density 1.5 t/m³.. Checked November 5, 2026