Paver calculator
Work out how many pavers to buy for a path, patio or driveway, how much gravel base and bedding sand goes under them, how deep to dig, and how much edging and polymeric sand you need, following the CMHA (ICPI) construction guide.
Paving
What it is for
CMHA: at least 4 in (100 mm) of compacted base on well-drained soil.
Areas to pave
Pavers
CMHA: 60 mm (2 3/8 in) for paths, patios and driveways.
Laying pattern
Adds 10 % for cuts (Western Interlock).
Joints
More settings
Thicker on wet or weak soil.
CMHA: 1 in (25 mm), screeded, not compacted.
Leave empty for 10 %.
Add this calculator to your website
Free for any website: paste this code where the calculator should appear. It keeps itself up to date, fits its height to the content and links back to the full page with the explanations.
How to use it
- 01Choose whether the paving is a path or patio or a driveway: a driveway needs a thicker base.
- 02Enter each area as a rectangle. Split an L-shaped patio into two rectangles.
- 03Enter the paver size from the product label and pick the laying pattern. Herringbone and diagonal layouts need more cuts.
- 04Read the pavers, the gravel and sand, the dig depth, the edging and the polymeric sand, then copy the list for the supplier.
How it is calculated
The layers follow the CMHA (formerly ICPI) construction guide for interlocking concrete pavements: a compacted gravel base, a 1 in bed of sand and the pavers on top. The allowance for cuts comes from the paver maker Western Interlock.
- Pavers
- n = ⌈A × (1 + allowance) / (l × w)⌉
- Gravel base
- V = A × base thickness (compacted)
- Bedding sand
- V = A × 1 in
- Dig depth
- base + sand + paver
- Fall
- ≥ 1.5 % × length
CMHA asks for at least 4 in of compacted base under paths and patios and 6 in under residential driveways, on well-drained soil. Wet or weak soils need more: increase the base under More settings.
The allowance is 10 % for straight patterns and 15 % for herringbone, diagonal or curved layouts, the lower end of the 15–20 % Western Interlock gives.
Tons are shown as a range because gravel and sand weigh different amounts depending on the material and how wet it is.
Worked example
A 16 × 12 ft patio with 4 × 8 in pavers
- Area 192 sq ft. With 10 % for cuts: 211.2 sq ft / 0.222 sq ft per paver = 951 pavers.
- Base 4 in: 64 cu ft = 2.37 cu yd, about 2.2 to 3.5 tons. Sand 1 in: 16 cu ft.
- Dig 4 + 1 + 2 3/8 = 7 3/8 in below the finished surface.
- Edging 56 ft, 3 to 4 bags of polymeric sand, and a fall of about 2.9 in over 16 ft.
Getting the order right
Compact in layers
CMHA spreads and compacts the base in lifts of 4 to 6 in. A thick base dumped in one go stays soft underneath and settles later.
Do not compact the sand
The bedding sand is screeded flat and left loose. The pavers are laid on it and the plate compactor then beds them in.
Slope away from the house
Give the surface at least 1.5 % fall away from walls so water runs off and does not soak the base.
Common mistakes
- Ordering the base as if loose gravel stayed the same volume after compaction.
- Using the same base for a driveway as for a patio.
- Laying pavers on a thick sand bed to make up for an uneven base.
- Forgetting the edge restraint, so the outer rows creep outwards.
Questions
How much base do I need under pavers?
CMHA gives at least 4 in (100 mm) of compacted gravel base for paths and patios and 6 in (150 mm) for driveways on well-drained soil, plus 1 in of bedding sand. Wet or clay soils need a thicker base.
How many pavers do I need?
Divide the area by the area of one paver and add 10 % for cuts, or 15 % for herringbone or diagonal patterns. A 192 sq ft patio in 4 × 8 in pavers takes 951.
How deep should I dig for a paver patio?
Add the base, the sand and the paver thickness: 4 + 1 + 2 3/8 in = 7 3/8 in for a patio with standard pavers.
How much polymeric sand do I need?
Rochester Concrete Products gives 60–75 sq ft per 50 lb bag for narrow joints and 25–40 sq ft for wide joints. Check the coverage printed on the bag you buy.
Guides on this topic
- Paver base depth for a patio or a driveway
Base thickness for pavers on patios and driveways, bedding sand, total excavation depth and waste for cut patterns, from CMHA and paver maker guides.
Related calculators
Sources
- [1]Construction of Interlocking Concrete Pavements (PAV-TEC-002-22). Concrete Masonry & Hardscapes Association (CMHA, formerly ICPI). Aggregate base at least 4 in (100 mm) for sidewalks and patios and 6 in (150 mm) for residential driveways on well-drained soils, thicker on wet or weak soils; bedding sand 1 in (25 mm) uncompacted; base compacted in 4–6 in lifts; joints 2–5 mm; slopes at least 1.5 %; pavers 60 mm thick for pedestrian areas and driveways.. Checked November 6, 2026
- [2]How to calculate paver stones needed for your project. Western Interlock (Basalite Building Products). Add 10 % for straight-lay patterns, 15–20 % for diagonal, herringbone or curved layouts.. Checked November 6, 2026
- [3]Paver Installation Guide (2018). Rochester Concrete Products. Base volume = paver area × base depth; polymeric sand, 50 lb bag per 60–75 sq ft with narrow joints or 25–40 sq ft with wide joints.. Checked November 6, 2026
- [4]Classification of aggregates (after Mindess, Concrete). Penn State University, CE 584 course library. Normal-weight aggregate (gravel, crushed stone): dry-rodded unit weight 1100 to 1750 kg/m³.. Checked November 5, 2026
- [5]Material conversions for winter parking lot and sidewalk maintenance. Minnesota Pollution Control Agency, Minnesota Stormwater Manual. Clean sand: 1 cubic yard = 1.4 tons (1.66 t/m³); weight varies with moisture.. Checked November 5, 2026
- [6]Produktdatenblatt Bruchsand 0/2. Leube Baustoffe. Crushed sand 0/2: bulk density 1.5 t/m³.. Checked November 5, 2026
Formulas and sources last checked on November 6, 2026. How we calculate