Skip to content
Yardox

Asphalt calculator

Find how many tonnes of asphalt to order for a driveway, path or yard.

Your surface

Area × compacted thickness × density of the laid asphalt, with the factors US highway departments use for estimating.

Size and mix

ft
ft
in

Thickness after rolling, per layer you are ordering.

%

For edges, low spots in the base and handling.

tons

Optional, to count truck loads.

Asphalt to order3.99 tons
Add this calculator to your website

Free for any website: paste this code where the calculator should appear. It keeps itself up to date, fits its height to the content and links back to the full page with the explanations.

How to use it

  1. 01Enter the length and width of the driveway, path or yard.
  2. 02Enter the thickness after rolling. For two layers, a base and a surface course, work out each layer separately.
  3. 03Choose the mix if you know it; otherwise keep the general estimate.
  4. 04Read the tonnes to order. Asphalt plants sell by weight, not by volume.

How it is calculated

Asphalt is ordered by weight. The weight is the compacted volume times the density of the rolled mix. US highway departments publish the factors they use to estimate quantities, and the calculator uses those.

Volume
length × width × compacted thickness
Weight
volume × density × (1 + extra)
US method
tons = yd² × lb per yd² per inch × inches / 2000

Washington State DOT estimates hot mix asphalt at 2.05 tons per cubic yard, about 2,430 kg/m³. Tennessee DOT lists factors per square yard and inch of thickness: 106 lb for a dense surface mix, 115 lb for a dense base mix and 88 lb for a porous open-graded mix. One pound per square yard and inch is 21.36 kg/m³.

The extra covers edges, low spots in the base and material left in the truck. The calculator starts at 5 %; a well-graded, rolled base needs less, a rough one more.

The calculator does not size the pavement. How thick the layers must be depends on the traffic and the ground, and is set by the contractor or a design.

Worked example

A 10 × 3 m driveway, 50 mm surface course

  1. Volume: 10 × 3 × 0.05 = 1.5 m³.
  2. Weight: 1.5 × 2,432 = 3,648 kg, plus 5 %: 3.83 t.
  3. The same drive in US units, 30 × 10 ft and 2 in of surface mix: 33.3 yd² × 106 × 2 / 2000 = 3.5 tons before the extra.

Getting the order right

Order by weight

Plants weigh every truck. Give them the tonnes, the mix and the time you can start laying, because hot mix has to be laid and rolled while it is hot.

Prepare the base first

Asphalt is only as good as the compacted base under it. The aggregate calculator finds the crushed stone for the base layer.

Measure the thickness after rolling

Loose asphalt behind the paver is thicker than the finished layer. Specify and check the compacted thickness.

Common mistakes

  • Using the loose thickness instead of the compacted one.
  • Counting a base and a surface course as one layer with one mix.
  • Ordering by volume from a plant that sells by weight.
  • Forgetting the extra for edges and an uneven base, and running short on the last metres.

Questions

How many tons of asphalt do I need for a driveway?

Area in square yards × 110 lb or so per square yard per inch × inches of thickness / 2000. A 30 × 10 ft drive with 2 in of surface mix needs about 3.5 tons.

How much does a cubic metre of asphalt weigh?

About 2.4 t once rolled. Washington State DOT estimates 2.05 tons per cubic yard, about 2,430 kg/m³; porous mixes are lighter.

How thick should a driveway be?

It depends on the traffic and the ground under it. Ask the contractor; the calculator works out the weight for whatever thickness is chosen.

Sources

  1. [1]WSDOT Design Manual M 22-01, Chapter 620, Exhibit 620-2: Estimating hot mix asphalt pavement. Washington State Department of Transportation. Hot mix asphalt for estimating: 137 lb per square yard for 0.10 ft compacted depth, which is 2.05 tons per cubic yard.. Checked November 11, 2026
  2. [2]Instructional Bulletin 16-11: Computations for asphalt mixes (2016-08-19). Tennessee Department of Transportation. Tons = area (yd²) × lb per yd² per inch of thickness / 2000. Factors: base mix grading A 115, surface mix grading D 106, open-graded friction course 88 lb per yd² per inch.. Checked November 11, 2026

Formulas and sources last checked on November 11, 2026. How we calculate