Skip to content
Yardox

Gravel and sand calculator

Work out the cubic metres or cubic yards of gravel, sand, topsoil or mulch for any area, the tonnes or tons to order and the number of bags.

Areas

01Area 1
Area 110 ft10 ft3 in

Material and bags

68.67–109.25 lb/ft³ for normal-weight aggregate (Mindess). Ask your supplier for the exact figure and enter it under Other.

%

Loose material settles when rolled. Ask the supplier for the factor; leave 0 for a top layer.

ft³

From the bag. Leave empty for bulk delivery.

lb

From the bag. Leave empty for bulk delivery.

To order0.86–1.37 tons· 0.93 yd³
Add this calculator to your website

Free for any website: paste this code where the calculator should appear. It keeps itself up to date, fits its height to the content and links back to the full page with the explanations.

How to use it

  1. 01Split the job into simple shapes: rectangles, circles and triangles. Add an area for each.
  2. 02Enter the depth the layer should have after spreading and, for a base, after compaction.
  3. 03Pick the material. Gravel, sand and topsoil show a weight range from published data; for the exact weight enter your supplier’s density under Other.
  4. 04If the layer will be compacted, add the supplier’s compaction factor as a percentage.
  5. 05Enter the bag size if you buy in bags, then copy the list.

How it is calculated

Volume is area times depth. Weight is volume times bulk density, which varies with the stone, the grading and the moisture, so the calculator shows a range unless you enter your supplier’s figure.

Rectangle
A = length × width
Circle
A = π × d² / 4
Triangle
A = base × height / 2
Volume
V = Σ A × depth
To order
V × (1 + compaction)
Weight
V × bulk density (min to max)
Bags
ceil(V / bag volume) or ceil(max weight / bag weight)

Published bulk densities: screened topsoil about 1.2 to 1.5 t/m³ (Holcim data sheet); crushed sand 0/2 1.5 t/m³ (Leube data sheet); clean sand 1.4 tons per cubic yard, which is 1.66 t/m³ (Minnesota Stormwater Manual); normal-weight aggregate 1100 to 1750 kg/m³ dry-rodded (Mindess).

One US ton is 2000 lb (907.18 kg); one cubic yard is 27 cubic feet (0.7646 m³).

Bags by weight are counted on the upper end of the range, so you do not run short.

Compaction is not a fixed number: it depends on the material and the roller. Ask the supplier, who knows the product.

Worked example

Bed of 10 × 10 ft, mulch 3 in deep, 2 cu ft bags

  1. Area: 10 × 10 = 100 sq ft.
  2. Volume: 100 × 0.25 ft = 25 cu ft = 0.93 cu yd.
  3. Bags: 25 / 2 = 12.5, so 13 bags.

Getting the order right

Order by the supplier’s numbers

Quarries sell by the ton and know their own density. Give them the volume and ask for the weight.

Depth is the expensive input

An inch more over a large yard adds a lot of material. Measure the depth you need, not the depth that looks right.

Check delivery access

Bulk trucks need a firm route and room to tip. Bags cost more per yard but can be carried.

Common mistakes

  • Using inches as feet: 3 in is 0.25 ft, not 3 ft.
  • Forgetting that a base layer shrinks when compacted.
  • Ordering dry sand weight for wet sand.
  • Counting one average density for every kind of gravel.

Questions

How much does a cubic yard of gravel weigh?

Normal-weight aggregate runs about 1100 to 1750 kg/m³, roughly 0.9 to 1.5 tons per cubic yard. Your quarry can give the exact figure for its stone.

How many bags of mulch for 100 sq ft at 3 in?

25 cu ft, so 13 bags of 2 cu ft.

How much sand is a ton?

At 1.4 tons per cubic yard (clean sand), one ton is about 0.71 cu yd. Wet sand is heavier.

Should I add extra?

For a compacted base, yes: ask the supplier for the compaction factor. For a loose top layer, a few percent covers uneven ground.

Guides on this topic

Sources

  1. [1]Produktdatenblatt Mutterboden, gesiebt 0/16 (Kieswerk Tönisvorst, 27.08.2020). Holcim (Deutschland) GmbH. Screened topsoil: bulk density about 1.2 to 1.5 t/m³.. Checked November 5, 2026
  2. [2]Produktdatenblatt Bruchsand 0/2. Leube Baustoffe. Crushed sand 0/2: bulk density 1.5 t/m³.. Checked November 5, 2026
  3. [3]Material conversions for winter parking lot and sidewalk maintenance. Minnesota Pollution Control Agency, Minnesota Stormwater Manual. Clean sand: 1 cubic yard = 1.4 tons (1.66 t/m³); weight varies with moisture.. Checked November 5, 2026
  4. [4]Classification of aggregates (after Mindess, Concrete). Penn State University, CE 584 course library. Normal-weight aggregate (gravel, crushed stone): dry-rodded unit weight 1100 to 1750 kg/m³.. Checked November 5, 2026

Formulas and sources last checked on November 5, 2026. How we calculate