Plaster calculator
Measure how far the wall is out at a few points, enter the walls and openings, and get the bags of plaster or skim filler to buy.
Walls and ceilings
Surfaces to plaster
A wall is its length × height; a ceiling its length × width. Several walls of one height can be one line: the room perimeter × height.
Doors and windows
Openings are not plastered. Leave them out for a small allowance for reveals.
Plaster thickness at several points
Hang a plumb line or set a long straightedge at the finished face and measure back to the wall at the high and low spots. Add the minimum coat at the high spots.
Product
0.86 kg/m² per mm, from 0.197 in, up to 1.969 in per coat and 1.969 in in total, bag 66 lb.
More settings: bag size, extra
Leave empty for 66 lb.
For mixing loss and droppings. The data sheets give none; 0 means exact.
Add this calculator to your website
Free for any website: paste this code where the calculator should appear. It keeps itself up to date, fits its height to the content and links back to the full page with the explanations.
How to use it
- 01Enter the walls (length × height) and ceilings (length × width). A room of one height can be one line: the perimeter × height.
- 02Add doors and windows. They are taken off the area.
- 03Set a plumb line or a long straightedge at the finished face and measure back to the wall at the high and low spots. Type a few of those thicknesses.
- 04Pick the plaster type and read the bags to buy. If a spot is too thick for one coat, the result says how many coats it needs.
How it is calculated
The amount of dry plaster is the area times the average thickness times the consumption the maker gives per square metre and millimetre.
- Area
- A = Σ length × height − openings
- Average thickness
- t = (t₁ + t₂ + … + tₙ) / n
- Dry mix
- m = A × t (mm) × consumption (kg/m²·mm)
- Bags
- n = m / bag weight, rounded up
- Coats
- thickest point / largest coat, rounded up
Consumption from the data sheets: Knauf Rotband Pro 8.6 kg/m² at 10 mm (0.86 per mm), 5 to 50 mm in one coat; Knauf MP 75 Diamant 12.0 kg/m² at 10 mm, at least 8 mm; Baumit KZP 65 about 1.4 kg/m² per mm, at least 10 mm inside and in several coats above 20 mm; Knauf Rotband Flächenspachtel Plus about 1.1 kg/m² per mm, up to 5 mm with the first coat up to 3 mm.
Knauf allows concrete ceilings only one coat of Rotband Pro, at most 15 mm thick.
In feet and inches the calculation is the same: thickness in inches, area in square feet, result in pounds and bags.
Worked example
Walls 48 × 8 ft with a door and two windows, gypsum plaster
- Walls: 48 × 8 = 384 ft². Door 3 × 6' 8" = 20 ft², windows 2 × 3 × 4 = 24 ft².
- Area: 384 − 20 − 24 = 340 ft² = 31.59 m².
- Thickness at four points: 3/8, 5/8, 3/4 and 1/2 in. Average 9/16 in = 14.3 mm.
- Dry mix: 31.59 × 14.3 × 0.86 = 388 kg = 856 lb.
- Bags of 30 kg (66 lb): 388 / 30 = 12.9 → 13 bags.
Getting the order right
Measure, do not guess
Old walls are rarely flat. Five or six readings across the worst wall change the result more than any waste factor.
Level first, skim after
Thick plaster fills the hollows; skim filler only smooths. Using filler for depth costs more and can crack.
Mind the drying time
Gypsum plaster must be dry before paint or tile. The bag gives the time per millimetre.
Common mistakes
- Taking the deepest point as the average thickness.
- Forgetting the minimum coat over the high spots.
- Buying skim filler for a wall that needs 10 mm of plaster.
- Ignoring the per-coat limit and applying 40 mm of lime-cement in one go.
Questions
How much plaster do I need per square metre?
At 10 mm, gypsum hand plaster needs about 8.6 kg/m² and machine plaster 12 kg/m². Thicker walls need proportionally more.
How thick can plaster be in one coat?
It depends on the product. Rotband Pro goes up to 50 mm, Baumit KZP 65 should be built up in several coats above 20 mm, skim filler only up to 3 mm per coat.
Should I subtract doors and windows?
Yes for the area. Leaving them in gives a small reserve for the reveals.
What is the difference between plaster and skim?
Plaster builds thickness and levels the wall; skim filler is a thin smooth finish of a few millimetres.
Guides on this topic
- How much plaster per square metre: consumption per mm and bags for a wall
Plaster and skim coat consumption per m² per mm from Knauf and Baumit data sheets, bags for a wall, and the layer limits you cannot go past.
Related calculators
Sources
- [1]Technisches Blatt Knauf Rotband Pro, Haftputzgips zum Glätten (P121a.de, 06/2014). Knauf Gips KG. Gypsum hand plaster: 8.6 kg/m² at 10 mm; one coat 5–50 mm, average 10 mm; concrete ceilings one coat up to 15 mm; 30 kg bag.. Checked November 5, 2026
- [2]Technisches Blatt Knauf MP 75 Diamant, Gipsmaschinenputz (P111a.de, 09/2013). Knauf Gips KG. Gypsum machine plaster: 12.0 kg/m² at 10 mm; wall average 10 mm, minimum 8 mm, up to 50 mm in one coat; 30 kg bag.. Checked November 5, 2026
- [3]Produktdatenblatt Baumit KalkzementPutz KZP 65 (Stand 10-05/20). Baumit GmbH. Lime-cement plaster: about 1.4 kg/m² per mm; base coat at least 10 mm inside, 15 mm outside; over 20 mm in several coats; 35 kg bag.. Checked November 5, 2026
- [4]Technisches Merkblatt Knauf Rotband Flächenspachtel Plus (10.2025). Knauf Bauprodukte GmbH & Co. KG. Ready-mixed skim filler: about 1.1 kg/m² per mm; 0–5 mm, first coat up to 3 mm; 4, 10, 20 kg pails.. Checked November 5, 2026
Formulas and sources last checked on November 5, 2026. How we calculate