Skip to content
Yardox

Siding calculator

Work out how many siding panels and boxes to order for the walls and gables of a house, plus starter strip, J-channel, outside corners and nails, using the estimating method of the Vinyl Siding Institute.

House

30 ft9 ft

Walls

Gables

Windows and doors

Panel

in

The visible height of one course, on the label or data sheet.

More settings
in

VSI: about 1 in where panel ends lap.

%

VSI: add 10 % to all estimates.

Panels to order149 panels· 7 boxes
Add this calculator to your website

Free for any website: paste this code where the calculator should appear. It keeps itself up to date, fits its height to the content and links back to the full page with the explanations.

How to use it

  1. 01Measure each wall: its width along the base and its height from the bottom of the siding to the soffit. Use the quantity for walls of the same size.
  2. 02Add the gables as triangles: the width at the base and the height from the base to the peak.
  3. 03List the windows and doors. They give the length of J-channel; their area is only deducted if you tick the box, which the VSI method reserves for large openings such as garage doors.
  4. 04Pick the panel you plan to buy or enter the length and exposure from its label, then the panels per box.
  5. 05Read the panels and boxes to order and the trim lengths, then copy the list for the supplier.

How it is calculated

We follow the estimating worksheet of the Vinyl Siding Institute: add up the wall rectangles and half of each gable rectangle, divide by what one panel covers and add 10 % for waste.

Walls
A walls = Σ W × H
Gables
A gables = Σ ½ × B × H
One panel
a = exposure × (length − overlap)
Panels
n = ⌈(A walls + A gables) × 1.10 / a⌉
Starter strip
Σ W (around the base)
J-channel
Σ 2 × (w + h) of openings + 2 × √((B/2)² + H²) per gable

Exposure is the part of a panel you see on the wall, for example 8 in on a double 4 in panel. Where panel ends overlap, about 1 in of length is hidden, so we take it off the length.

Windows and doors are usually not deducted because the cuts around them waste as much as the opening saves. That is also why the 10 % allowance is not reduced for houses with many windows.

We round only once, when counting panels and boxes.

Worked example

A 30 × 24 ft house, 9 ft walls, two 24 × 6 ft gables

  1. Walls: 2 × 30 × 9 + 2 × 24 × 9 = 972 sq ft. Gables: 2 × ½ × 24 × 6 = 144 sq ft. Total 1,116 sq ft, about 11.2 squares.
  2. One ABTCO D4D panel covers 8 in × (150 − 1) in = 8.28 sq ft.
  3. With 10 %: 1,227.6 / 8.28 = 148.3, so 149 panels, which is 7 boxes of 24.
  4. Starter strip: 108 ft around the base. Four outside corners at 9 ft: 36 ft of corner post.

Getting the order right

Order trim from the same batch

Corner posts, J-channel and panels are colour-matched by the manufacturer. Ordering everything at once avoids small colour differences between deliveries.

Stagger the joints

The VSI asks for panel seams at least 2 ft apart from one course to the next. Plan the first courses so joints do not line up.

Leave room to move

Vinyl expands and contracts. Leave ¼ in clearance in receiving channels, and nail in the centre of the slots without driving the head tight.

Common mistakes

  • Counting the gables as full rectangles: that doubles their area.
  • Using the full panel length instead of the length minus the overlap.
  • Deducting every window and then running short because of the cuts around them.
  • Forgetting the J-channel along the gable rakes.

Questions

How many squares of siding do I need?

A square is 100 sq ft. Add up the walls (width × height) and half of each gable (base × height), then divide by 100. A 30 × 24 ft house with 9 ft walls and two 6 ft gables is 1,116 sq ft, or 11.2 squares before waste.

How much waste should I add to siding?

The Vinyl Siding Institute adds 10 % to all material estimates. Complex walls with many corners and dormers can need more.

Do I subtract windows and doors?

Usually not. The VSI estimating method keeps them in, because the cuts around openings waste roughly what the opening saves. Large openings like garage doors or sliding doors can be deducted.

How many nails per siding panel?

Fasteners go at most 16 in apart on horizontal panels, so a 12 ft 6 in panel takes about 10 nails, centred in the slots and not driven tight.

Guides on this topic

Sources

  1. [1]Vinyl Siding Installation Manual (2016). Vinyl Siding Institute. Estimating: walls height × width, gables ½ × height × width, windows and doors usually not deducted (large openings may be), add 10 % for waste, starter strip = length around the base, a square = 100 sq ft. Panel ends overlap about 1 in; fasteners at most 16 in apart on horizontal panels.. Checked November 6, 2026
  2. [2]Quick Tips for Installing Horizontal Vinyl Siding (2020). Vinyl Siding Institute. Overlap panels by 1 in; keep panel seams at least 2 ft apart; ¼ in clearance in receiving channels.. Checked November 6, 2026
  3. [3]ABTCO Cedar Creek D4D Double Dutchlap 4 in × 150 in, 24/box – product page. The Home Depot Canada. 8 in exposure, 150 in (12 ft 6 in) long, about 8.33 sq ft per piece, 24 pieces and 200 sq ft per carton.. Checked November 6, 2026
  4. [4]Docke LUX Brus D6S – product page. Docke. Working dimensions 3600 × 300 mm, working area 1.08 m², 16 pieces per box.. Checked November 6, 2026

Formulas and sources last checked on November 6, 2026. How we calculate